LCM of 3 Numbers Calculator LCM of 4 Numbers Calculator LCM of 5 Numbers Calculator LCD Calculator How to find LCM LCM and HCF Questions Least Common Denominator Calculator Greatest Common Divisor Calculator HCF Calculator HCF of 3 Numbers Calculator HCF of 4 Numbers Calculator GCD Calculator Greatest Common Factor Calculator Least Common Multiple Calculator Common Factors Calculator

300+ TOP Microprocessors Questions and Answers | MCQs

MICROPROCESSORS Questions :-

1. The minimum number of transistors required to implement a two input AND gate is

A. 2
B. 4
C. 6
D. 8

2. Using DeMorgan’s Theorem we can convert any AND-OR structure into

A. NAND-NAND
B. OR-NAND
C. NAND-NOR
D. NOR-NAND

3. For a memory with a 16-bit address space, the address ability is
A. 16 bits
B. 8 bits
C. 2^16 bits
D. Cannot be determined

4. Because we wish to allow each ASCII code to occupy one location in memory, most memories are _____ addressable.
A. BYTE
B. NIBBLE
C. WORD (16 bits)
D. DOUBLEWORD (32 bits)

5. Circuit A is a 1-bit adder; circuit B is a 1 bit multiplier.

A. Circuit A has more gates than circuit B
B. Circuit B has more gates than circuit A
C. Circuit A has the same number of gates as circuit B

(Hint: Construct the truth table for the adder and the multiplier)

6. When the write enable input is not asserted, the gated D latch ______ its output.
A. can not change
B. clears
C. sets
D. complements

7. A structure that stores a number of bits taken “together as a unit” is a
A. gate
B. mux
C. decoder
D. register

8. We say that a set of gates is logically complete if we can build any circuit without using any other kind of gates. Which of the following sets are logically complete
A. set of {AND,OR}
B. set of {EXOR, NOT}
C. set of {AND,OR,NOT}
D. None of the above

9. Of the following circuits, the one which involves storage is
A. RS Latch
B. mux
C. nand
D. decoder

10. If the number of address bits in a memory is reduced by 2 and the
address ability is doubled, the size of the memory (i.e., the number of bits stored in the memory)
A. doubles
B. remains unchanged
C. halves
D. increases by 2^(address bits)/addressability

12. If m is a power of 2, the number of select lines required for an m-input mux is:

A. m
B. 2^m
C. log2 (m)
D. 2*m

13. For the number A[15:0] = 0110110010001111, A[14:13] is ______ A[3:2].

A. less than
B. greater than
C. the same as
d . cannot be determined

14. Which of the following conditions is not allowed in an RS latch?

A. R is asserted, S is asserted
B. R is asserted, S is negated
C. R is negated, S is asserted
D. R is negated, S is negated

15. Which of the following pair of gates can form a latch?
A. a pair of cross coupled OR
B. a pair of cross copled AND
C. a pair of cross coupled NAND
D. a cross coupled NAND/OR

16. ‘Burst refresh’ in DRAM is also called

A. Concentrated refresh
B. Distributed refresh
C. Hidden refresh
D. None of the above

17. The number of interrupt lines in 8085 is

A. 2
B. 3
C. 4
D. 5

18. A real number consists of

A. integer part
B. integer part and fraction part
C. integer part, fraction part along with positive or negative sign
D. none of the above

19. Assertion (A): Negative values of incremental operator in DO loop are allowed in Fortran 77 but not in earlier versions of Fortran.

Reason (R): Fortran 77 has better array facilities than earlier versions of Fortran.

A. Both A and R are correct and R is correct explanation of A
B. Both A and R are correct but R is not correct explanation of A
C. A is correct R is wrong
D. A is wrong R is correct

20. Which of the following is not treated as hexadecimal constant by assembler in 8085?

A. 45 H
B. 6 AFH
C. 234
D. 64 H

21. IC 7485 cannot be cascadeD.

A. True
B. False

22. An I/O processor controls the flow of information between

A. cache memory and I/O devices
B. main memory and I/O devices
C. two I/O devices
D. cache and main memory

23. MS Access is a DBMS software.

A. True

B. False

24. When .9432 E – 4 is subtracted from .5452 E – 3 in normalized floating point mode

A. none of the numbers is changed
B. .9432 E – 4 is changed to .09432 E – 3 and .5452 E – 3 is not changed
C. .5452 E – 3 is changed to 5.452 E – 4 but .9432 E – 4 is not changed
D. both Ihe numbers are changed and their exponents are, made equal to -5

25. DS directive in 8085

A. forces the assembler to reserve one byte of memory
B. forces the assembler to reserve a specified number of bytes in the memory
C. forces the assembler to reserve a specified number of consecutive bytes in the memory
D. none of the above

26. Which of the following is a valid integer constant?

A. 127
B. 127.0
C. 127
D. 125 + 3

27. The five flags in 8085 are designated as

A. Z, CY, S, P and AC
B. D, Z, S, P, AC
C. Z, C, S, P, AC
D. Z, CY, S, D, AC

28. In 8085 which addressing mode is also called inherent addressing?

A. Direct
B. Register
C. Implicit
D. Immediate

29. It is possible to copy a file in the same directory.

A. True
B. False

30. In a computer the data transfer between hard disk and CPU is nearly the same as that between diskette and CPU.

A. True
B. False

31. The timing difference between a slow memory and fast processor can be resolved if

A. processor is capable of waiting
B. external buffer is used
C. either (a) or (b)
D. neither (a) nor (b)

32. In 8086 the number of bytes which can be addressed directly is about

A. 1000
B. 10000
C. 100000
D. one million

33. In Fortran 77 a variable name can contain special characters.

A. True
B. False

34. Which of the following is not a general purpose peripheral?

A. I/O port
B. Programmable interrupt controller
C. Programmable CRT controller
D. Programmable interval timer

35. Each instruction in assembly language program has the following fields:

  1. Lable field
  2. Mnemonic field
  3. Operand field
  4. Comment field
    The correct sequence of these fields is?

A. 1, 2, 3, 4
B. 1, 2, 4, 3
C. 2, 1, 3, 4
D. 2, 1, 4, 3

36. In one’s complement 8 bit representation 11111111 represents

A. +0
B. -0
C. +1
D. -1

37. The operating modes of 8255 A are called

A. mode 0 and mode 1
B. mode 0, mode 1 and mode 2
C. mode 0 and mode 2
D. mode 0, mode 2 and mode 3

38. Which of the following is type declaration statement in C?

A. int bar
B. s = s + 1
C. king = horse + 1
D. prin = prin * prin

39. Internet is a worldwide network of computers where most of the information is freely available.

A. True
B. False

40. A 37 bit mantissa has an accuracy of

A. 6 decimal places
B. 8 decimal places
C. 10 decimal places
D. 11 decimal places

41. In a C expression using assignment operators, relational operators and arithmetic operators, the hierarchy of operations (in the absence of parenthesis) is

A. assignment, relational, arithmetic
B. relational, assignment, arithmetic
C. arithmetic, assignment, relational
D. arithmetic, relational, assignment

42. In 8085, the pins for SID and SOD are

A. 4 and 5 respectively
B. 5 and 4 respectively
C. 3 and 4 respectively
D. 4 and 3 respectively

43. Assertion (A): Each memory chip has its own address latch.

Reason (R): ALE signal comes out of microprocessor 8085 and goes to memory chip.

A. Both A and R are correct and R is correct explanation of A
B. Both A and R are correct but R is not correct explanation of A
C. A is correct R is wrong
D. A is wrong R is correct

44. An e-mail message can be sent to many recipients.

A. True
B. False

45. In C the keywords are also called

A. special words
B. reserved words
C. class words
D. character words

46. The character set of Fortran 77 includes lower case alphabets a to z.

A. True
B. False

47. Which memory has read operation, byte erase, byte write and chip erase?

A. RAM
B. UVEPROM
C. EEPROM
D. both (b) and (c)

48. The forms of IF statements in FORTRAN 77 are called

A. logical IF and Block IF
B. logical IF, block IF and arithmetic IF
C. logic IF, block IF, arithmetic IF and negate IF
D. logical IF and arithmetic IF

49. In 8085

A. P flag is set when the result has even parity
B. P flag is set when the result has odd parity
C. P flag is reset when the result has odd parity
D. P flag is reset when the result has even parity

50. If the sign bit of mantissa is 0 and the exponent is increased from a positive to a more negative number the result is

A. a larger floating point number
B. a smaller floating point number
C. either (a) or (b) depending on the actual number
D. a negative floating point number